How to calibrate a PS5 or PS4 controller
Sony’s support pages for the DualSense and the DualShock 4 offer a reset, not a stick calibration. So calibrating a PlayStation pad means one of three things: that reset, a deadzone on your PC, or an open-source tool that recalibrates the sticks over USB. Read your sticks in the tester below before you try any of them.
Start designing
Press any button on your controller
Connect it by USB or Bluetooth first. A browser shows a controller to a page only after a button has been pressed.
Measure your sticks first
Every fix below changes either where the middle of a stick is, or how much movement around the middle gets ignored. Without a number from before, you cannot tell what a fix did.
Connect the DualSense or DualShock 4 to this computer, by USB or Bluetooth, and press any button. The tester at the top of this page shows what your browser receives.
- Take your thumbs off both sticks and read “Off centre” under each plot: the distance from the middle, as a share of full travel. A few percent is normal.
- Switch on a deadzone ring. The buttons above the plots draw a dashed ring at 5%, 10% or 15%. A resting dot outside the ring would move your camera in a game that ignores only that much.
- Flick each stick and let it snap back, several times. Note whether it comes back to the same number.
- Rotate each stick around its edge until a circularity figure appears.
Keep the numbers. There is a page for each pad, the PS5 DualSense tester and the PS4 controller tester, and the stick drift test explains the readings.
What Sony offers
PlayStation Support has a troubleshooting page for each controller: the DualSense and the DualShock 4. Both start the same way: “If you’re having issues with your controller, try resetting it.” After the reset they branch into button or analog stick issues, vibration, pairing, disconnects and battery.
Neither page has a step called calibration. The DualSense page adds one thing worth doing first: if you can use your PS5, update its system software to the latest version.
That is why most of this page is about a computer. The two ways to move a PlayStation stick’s centre, or to hide a small offset, both run on a PC.
Reset the controller
Sony’s steps for the DualSense:
- Turn off the PS5.
- Disconnect the controller from the USB cable.
- Find the reset button inside the small hole next to the Sony logo on the back of the controller.
- Press and hold it with a pin or a similar tool for at least 5 seconds.
- Connect the controller to the console with the USB cable that came with it, and press the PS button.
For the DualShock 4 the steps are the same, with two differences. Sony has you turn off and unplug the PS4, and the hole is on the back near the L2 button. An unfolded paper clip is Sony’s own suggestion for the tool.
A reset is safe to try. Sony says it “will not reconfigure the controller or affect pairing settings”. We have not measured what a reset does to a stick’s resting value, so measure it yourself: read “Off centre” again afterwards and compare.
A deadzone on PC
A deadzone repairs nothing. It tells the software to ignore stick movement below a set amount, and that is enough for a stick that rests a little off the middle but always in the same place.
Steam has a deadzone for every game it launches. Open Settings, then Controller, then Calibration & Advanced Settings, and go to the joystick page. Each stick has a slider, and the screen can show the stick’s live input, so you see the drift you are covering.
Set it just above the “Off centre” number you measured. Everything inside the deadzone is travel the game no longer feels, so more is not better. On a console, look in the game’s own controller settings: many games have a deadzone of their own.
Recalibrate over USB in the browser
There is an open-source tool that does what the console does not. The DualShock Calibration GUI describes itself as “a web-based calibration tool for PlayStation DualShock 4, DualSense, and DualSense Edge controllers using the WebHID API”. Its feature list names stick calibration and range calibration, and it is published under the MIT licence at dualshock-tools.github.io.
What its README says about where it runs: only in browsers with WebHID support, which it lists as Chrome, Edge and Opera. Nothing is installed.
Two things to know before you use it. It is a community project, not a Sony tool. And we have not run it on a controller ourselves, so we cannot tell you what it will do to yours. If you try it, use this page as the independent check: measure before, measure after, and flick the sticks a few times to see whether the new centre holds.
If the wrong buttons light up
This one looks like a fault and is not. Next to the controller’s name the tester says either “Standard mapping” or “Non-standard mapping”. Over Bluetooth a Sony pad sometimes reaches the browser in a non-standard order, so pressing Square lights Cross on the drawing. The buttons work. The browser is reporting them in another order, and over USB they usually arrive in the standard one.
It matters if you show the pad on stream. The PS5 controller overlay and the PS4 controller overlay correct the common orders by themselves.
When nothing helps
Calibration moves a centre. It suits a stick that always rests at the same few percent. A stick that lands somewhere different on every release has no single centre to move, and a deadzone wide enough to cover it costs you fine control.
Microsoft, which does ship an official recalibration tool for its own pads, says of it that drift from normal wear and tear cannot be resolved that way. The same limit applies here. At that point Sony’s troubleshooting pages are the next stop: pick “Button or analog stick issue” and follow it to a repair or replacement.
Holding an Xbox pad as well? Microsoft’s tool is covered in how to calibrate an Xbox controller. And if you stream, the pad drawn at the top of this page can sit in the corner of your stream in OBS, Streamlabs Desktop or TikTok LIVE Studio. If you are coming from Gamepad Viewer, see Gamepad Viewer skins and the Gamepad Viewer alternative page.


