ControllerOverlay

How to calibrate an Xbox controller on PC and console

Microsoft has a recalibration tool for sticks and triggers in the Xbox Accessories app, on Xbox consoles and on Windows. Read your sticks in the tester below first, run the tool, then read them again to see whether it helped.

Start designing

Press any button on your controller

Connect it by USB or Bluetooth first. A browser shows a controller to a page only after a button has been pressed.

Measure your sticks before you change anything

Recalibrating moves where the controller thinks the middle of a stick is. If you do not write down where the stick rests now, you cannot tell afterwards whether anything changed.

Connect the controller to this computer, by USB or Bluetooth, and press any button. The tester at the top of this page shows what your browser receives from it.

  1. Take your thumbs off both sticks and read “Off centre” under each plot. That is how far the stick rests from the middle, as a share of its full travel. A few percent is normal.
  2. Switch on a deadzone ring. The buttons above the plots draw a dashed ring at 5%, 10% or 15%. A resting dot outside the ring would move your camera in a game that ignores only that much.
  3. Flick each stick and let it snap back, a few times in different directions. Note whether it returns to the same number each time.
  4. Pull LT and RT slowly to the end. Each should start at 0.00 and reach 1.00.

Keep the numbers. The Xbox controller tester explains every reading, and the stick drift test goes through drift step by step.

Which Xbox controllers can be recalibrated

Microsoft added the stick tool in its February 2024 update for Xbox Wireless Controllers, describing it as a way to address “minor thumbstick issues such as inconsistent responses”. The November 2024 update extended it to the Elite Series 2.

Today Xbox Support puts it in one sentence: the tool “is currently available for the Xbox Wireless Controller and Xbox Elite Wireless Controller Series 2 only”.

If you hold another controller, the Xbox Accessories app is not where its calibration lives. Look at the maker’s own software, or use a deadzone as described further down.

Update the controller first

The tool sits on the same screen as the firmware version, and the published walkthroughs install any update before recalibrating.

  • On an Xbox console: press the Xbox button, open Profile & system, then Settings, Devices & connections, and the controllers entry. Select your controller and open the “…” menu. If an update is offered, install it.
  • On Windows: install Xbox Accessories from the Microsoft Store and connect the controller with a USB cable. Open the same “…” menu on the controller’s screen.

Recalibrate the sticks

  1. On the “…” screen, choose the recalibration options.
  2. Pick the left or the right stick.
  3. Follow the instructions on screen until the tool says it is done.
  4. Repeat for the other stick if it needs it.

What the tool does, in the words of a controller repair shop that documents it for its customers: it samples where the stick sits naturally and resets the X and Y defaults to (0, 0), so the centre of the stick sits closer to a true zero.

Microsoft adds one case where you should always run it: after a self-repair. If you have replaced the controller’s base and circuit board, the old calibration values no longer match the parts.

Now come back to the tester and read “Off centre” again, thumbs off. Compare it with the number you wrote down.

Recalibrate the triggers

The same November 2024 update added a trigger calibration, “for players experiencing minor trigger issues”, on the Xbox Wireless Controller and the Elite Series 2. It is in the same recalibration options.

Use it if a trigger did not reach 1.00 at full pull in the tester, or did not come back to 0.00. Afterwards pull both triggers slowly again and watch the numbers climb.

A deadzone in Steam, for what calibration leaves

A deadzone does not repair anything. It tells the software to ignore stick movement below a set amount, which hides a small resting offset.

Steam has one for every game it launches. Open Settings, then Controller, then Calibration & Advanced Settings, and go to the joystick page. Each stick has a deadzone slider, and the screen can show the stick’s live input so you can see the drift you are covering.

Set it a little above the “Off centre” figure you measured, and no higher: everything inside the deadzone is travel the game no longer feels. Many games also have their own deadzone setting, and Microsoft’s advice for drift that shows in only one game is to check that game’s settings.

When recalibration does not help

Xbox Support says it plainly: “Not all stick or trigger issues can be resolved with this recalibration tool, including drift due to normal wear and tear.”

A way to tell the two apart with the tester: a stick that always rests at the same few percent has a shifted centre, which is what the tool moves. A stick that lands somewhere different on every release has no single centre to move.

Before giving up on the controller, the other steps published alongside the tool are short:

  • restart the controller by holding the Xbox button for 5 to 10 seconds, then turn it back on
  • try another USB cable
  • try the controller on another device
  • ask for a replacement if it is under warranty

If you play PlayStation pads as well, calibrating a PS5 or PS4 controller works differently. And if you stream, the same drawing of the pad you see above can sit in the corner of your stream: the Xbox controller overlay goes into OBS, Streamlabs Desktop or TikTok LIVE Studio as one link. People coming from Gamepad Viewer can read Gamepad Viewer skins and the Gamepad Viewer alternative page.

Xbox controller calibration questions

Install the Xbox Accessories app from the Microsoft Store and connect the controller with a USB cable. On the controller’s screen open the “…” menu, choose the recalibration options, pick the left or right stick and follow the instructions on screen.

More from the blog

All posts